Hantek DSO5102P USB Digital Storage Oscilloscope 2Channels 100MHz 1GSa/s

Description
Hantek DSO5102P USB Digital Storage Oscilloscope 2Channels 100MHz 1GSa/s
Features
100MHz bandwidths
1GSa/s Real Time sample rate
Large (7.0-inch) color display,WVGA(800×480)
Record length up to 40K
Trigger mode:edge/pulse width/line selectable video/slop/overtime etc.
USB host and device connectivity, standard
Multiple automatic measurements
Four math functions, including FFTs standard
Provides software for PC real-time analysis
Specification
Model:DSO5202P:DSO5102P:DSO5072P
Acquisition
Sample Rate:Real-Time Sample:1GS/s
Equivalent Sample:25GS/s
Acquisition Modes::
Normal:Normal data only
Pea’k Detect:High-frequency and randon glith capture
Average:Wavefom Average, selectable 4,8,16,32,64,128
Inputs
Inputs Coupling:AC, DC, GND
Inpits Impendance:1MΩ±2% II20pF±3pF
Probe Attenuation:1X, 10X
Supported Probe Attenuation Factor:1X, 10X, 100X, 1000X
Maximum Input Voltage:CAT I and CAT II:300VRMS (10*), Installation Category;
CAT III:150VRMS (1*);
Installation Category II:derate at 20dB/decade above 100kHz to 13V Pea’k AC at 3MHz* and above.
For non-sinusoidal waveforms, Pea’k value must be less than 450V.
Excursion above 300V should be of less than 100ms duration.
RMS signal level including all DC components removed through AC coupling must be limited to 300V.
If these values are exceeded, damage to the oscilloscope may occur.
Horizontal
Sample Rate Range:500MS/s–1GS/s
Waveform Interpolation:(sin x)/x
R’ecord Length:40’K
SEC/DIV Range:4ns/div to 40s/div:4ns/div to 40s/div
Sample Rate and
Delay Time Accuracy:±50ppm(at over any ≥1ms time interval)
Position Range:2ns/div to 10ns/div;
(-4div x s/div) to 20ms;:20ns/div to 80us/div; (-8div x s/div) to 40ms;
200us/div to 40s/div; (-8div x s/div) to 400s
Incremental Time Measurement Accuracy
(Full Bandwidth):Single-shot, Normal mode:± (1 sample interval +100ppm * reading + 0.6ns);
>16 averages:± (1 sample interval + 100ppm * reading + 0.4ns);
Sample interval = s/div ÷ 200
Vertical
Vertical Resolution:8-bit resolution, all channel sampled simultaneously
Position Range:2mV/div to 200mV/div, ±2V
200mV/div to 5V/div, ±50V
Bandwidth:100MHz:100MHz:70MHz
Rise Time at BNC( typical):3.5ns:3.5ns:5ns
Analog Bandwidth in Normal and
Average modes at BNC or with probe, DC Coupled:2mV/div to 20mV/div, ±400mV; 50mV/div to 200mV/div, ±2V
500mV/div to 2V/div, ±40V; 5V/div, ±50V
Math:+, -, *, /, FFT
FFT:Windows:Hanning, Flatop, Rectamgular, Bartlett, Blackman;
1024 sample point
Bandwidth Limit:20MHz
Low Frequency Response (-3db):≤10Hz at BNC
DC Gain Accuracy:±3% for Normal or Average acquisition mode, 5V/div to 10mV/div;
±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div
DC Measurement Accuracy,
Average Acquisition Mode:When vertical displacement is zero, and N ≥16:± (3% * reading + 0.1div + 1mV) only 10mV/div or greater is selected;
When vertical displacement is not zero, and N≥16:± [3% * (reading + vertical position) + 1% of vertical position + 0.2div];
Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/div
Volts Measurement Repeatability,
Average Acquisition Mode:D1elta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions
Trigger System
Trigger Types:Edge, Video, Pulse, Slope, Over time, Alternative
Trigger Source:CH1, CH2, EXT, EXT/5, AC Line
Trigger Modes:Auto, Normal, Single
Coupling Type:DC, AC, Noise Reject, HF Reject, LF Reject
Trigger Sensitivity
(Edge Trigger Type):DC(CH1,CH2)
1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full;
DC(EXT)
200mV from DC to 100MHz; 350mV from 100MHz to 200MHz;
DC(EXT/5)
1V from DC to 100MHz;1.75V from 100MHz to 200MHz;
AC:Attenuates signals below 10Hz;
HF Reject:Attenuates signals above 80kHz;
LF Reject:Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz
Trigger Level Range:CH1/CH2:±8 divisions from center of screen;
EXT:±1.2V;
EXT/5:±6V
Trigger Level Accuracy( typical)Accuracy
is for signals having rise and fall times ≥20ns:CH1/CH2:0.2div * volts/div within ±4 divisions from center of screen;
EXT:± (6% of setting + 40mV);
EXT/5:± (6% of setting + 200mV);
Set Level to 50%(typical):Operates with input signals ≥50Hz
Video Trigger
Video Trigger Type:CH1, CH2:Pea’k-to-Pea’k amplitude of 2 divisions;
EXT:400mV;
EXT/5:2V
Signal Formats and Field Rates, Video Trigger Type:Supports NTSC, PAL and SECAM broadcast systems for any field or any line
Holdoff Range:100ns ~ 10s
Pulse Width Trigger
Pulse Width Trigger Mode:Trigger when (
, = , or ≠); Positive pulse or Negative pulse
Pulse Width Trigger Point:Equal:The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level.
Not Equal:If the pulse is narrower than the specified width, the trigger point is the trailing edge.
Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.
Less than:The trigger point is the trailing edge.
Greater than (also called overtime trigger):The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width
Pulse Width Range:20ns ~ 10s
Slope Trigger
Slope Trigger Mode:Trigger when (
, = , or ≠ ); Positive slope or Negative slope
Slope Trigger Point:Equal:The oscilloscope triggers when the waveform slope is equal to the set slope.
Not Equal:The oscilloscope triggers when the waveform slope is not equal to the set slope.
Less than:The oscilloscope triggers when the waveform slope is less than the set slope.
Greater than:The oscilloscope triggers when the waveform slope is greater than the set slope.
Time Range:20ns ~ 10s
Overtime Trigger
Over Time Mode:Rising edge or Falling edge
Time Range:20ns ~ 10s
Alternative Trigger
Trigger on CH1:Internal Trigger:Edge, Pulse Width, Video, Slope
Trigger on CH2:Internal Trigger:Edge, Pulse Width, Video, Slope
Trigger Frequency Counter
Readout Resolution:6 digits
Accuracy (typical):±30ppm (including all frequency reference errors and ±1 count errors)
Frequency Range:AC coupled, from 4Hz Min to rated bandwidth
Signal Source:Pulse Width or Edge Trigger modes:all available trigger sources
The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses
due to changes in the run status, or acquisition of a single shot event has completed.
Pulse Width Trigger mode:The oscilloscope counts pulses of significant amplitude inside the 1s measurement window that qualify as triggerable events,
such as narrow pulses in a PWM pulse train if set to
Edge Trigger mode:The oscilloscope counts all edges of sufficient amplitude and correct polarity.
Video Trigger mode:The Frequency Counter does not work.
Measure
Cursor Measurement:Voltage difference between cursors:ΔV
Time difference between cursors:ΔT
Reciprocal of ΔT in Hertz (1/ΔT)
Auto Measuerment:Frequency, Period, Mean, Pk-Pk, Cycli RMS, Min, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF
Display
Display Type:7 inch 64K color TFT (diagonal liquid crystal)
Display Resolution:800 horizontal by 480 vertical pixels
Display Contrast:Adjustable (16 gears) with the progress bar
Probe Compensator Output
Output Voltage( typical):About 5Vpp into ≥1MΩ load
Frequency(typical):1kHz
Power Supply
Supply Voltage:100-120VACRMS(±10%), 45Hz to 440Hz, CATII
120-240VACRMS(±10%), 45Hz to 66Hz, CATII
Power Consumption
Fuse:2A, T rating, 250V
Environmental
Temperature:Operating:32F to 122F (0C to 50C);
Nonoperating:-40F to 159.8F (-40C to +71C)
Cooling Method:Convection
Humidity:+104F or below (+40C or below):≤90% relative humidity;
106F to 122F (+41C to 50C):≤60% relative humidity
Altitude:Operating:Below 3,000m (10,000 feet);
Nonoperaring:Below 15,000m(50,000 feet)
Mechanical
Size:Length 385mm, Width 200mm, Height 245mm
Weight:3.5KG(with Packing); 2.08KG(without Packing)
Package includes
1 x Digital Storage Oscilloscope
2 x Probes (PP150)
1 x Oscilloscope Power Cable
1 x USB line
1 x Hantek data CD
1 x Manufacturer Certificate